1 496

ECF11_vol 1

A comparative numerical study of the ductile tearing in welded joints using a global and a local approach 1
A fracture mechanics model for interacting cracks in thermal fatigue 5
A model of damage and fracture based on fuzzy sets theory 9
A new simplified method for calculating J integral - the elastic plastic stress state method 13
A simple method for the determination of geometric correction factors in linear elastic fracture mechanics 17
A weight function for stress intensity factor evaluation in steel bridges orthotropic decks 21
An analysis of the brittle fracture mechanism in cast steel 25
An interface crack with bonding in its end regions and the adhesion fracture energy 29
Analysis of J-integral dependence on stress hardening exponent for finite non-linear elastic cracked body 33
Analytical solution of three-dimensional problem for elliptical crack subjected to arbitrary time-harmonic loads 37
Application of fracture mechanics in the design and operation of nuclear PWR in France 41
Application of the gash model for analysis of dynamic behavior of a rotor with a crack 47
Assessing the effectiveness of toughening agents 51
Assessment of fatigue precracking methods for fracture toughness testing of Q+T weldments 55
Asymptotic fields of a mode III crack meeting an inclined interface between two elastic-plastic materials 59
Asymptotic method in the plane theory problem for the orthotropic strip with cuts 63
Behaviour of cracked cylinders under combined thermal and mechanical loading 67
Boundary integro-differential equations for anisotropic crack problems 71
Characterising fracture in polymers and composites 75
Characteristics of fracture behaviour of duplex steels in transition region 79
Characterization of interfacial fracture of diffusion bonded bi-material joints of Ti alloys 83
Circumferential surface cracks in pipes 87
Cohesive zone model for ductile fracture. Comparison of prediction with experiment 91
Computer code for calculating the factor of safety against fracture and the fatigue crack propagation 95
Conception of cohesive forces in nonlinear fracture mechanics 99
Corrosion and temperature effects on crack kinetics in steels 103
Crack kinking in anisotropic materials 109
Crack tip fields for rapidly growing cracks in viscoplastic materials 113
Crack tip plasticity investigation using Dugdale strip yield model approach 117
Cyclic fatigue - crack growth in toughened ceramics and intermetallics at ambient to elevated temperatures 121
Damage accumulation criterion for multiaxial high and low cycle fatigue 130
Damage and crack growth modelling by fracture process zone 134
Damage tolerance analyses of bolt nut assemblies 138
Dynamic compression and fracture of plain carbon steel 143
Dynamic crack propagation and crack arrest behaviour of two low alloy steels 147
Dynamic fracture of armor steel 151
Edge toughness of brittle materials 155
Effect of strain ageing on the fracture toughness and tensile properties of Si-killed C-Mn steels 159
Effects of (initial) fracture mode on fracture toughness and or stress intensity 163
Effects of residual stress on fracture toughness and subcritical growth of indented cracks in glasses 167
Effects of residual stresses induced by shot peeing on cracks propagation 171
Effects of small defects and inhomogeneities on fatigue strength experiments, model and applications to industry 175
ESIS TC6 round robin on fracture toughness of ceramics 182
Estimation of the R-curve by in situ measurements 186
Experimental and numerical investigations on cleavage fracture 190
FE modelling of delamination growth in DCB specimens with material variability or geometric imperfections 194
Finite element simulation of the fracture behaviour of elastomers within a large transformation framework 198
Fracture behaviour of ultra-low carbon bainitic steels for heavy section applications 202
Fracture due to solid structural transformation 206
Fracture energy and mechanical behaviour of clay elements 210
Fracture evolution and snap-back instability in multi-cracked finite plates 214
Fracture instabilities and scale effects in brittle solids and brittle matrix fibrous composites 218
Fracture of a semi-infinite medium containing a macrocrack and microcracks 224
Fracture of epoxy bonded dynamic peel specimens containing interfacial layers 228
Fracture of rubbers experimental and numerical determination of the J integral 232
Fracture propagation in cast irons 236
Fracture toughness of an isothermally forged y -Titanium Aluminide 240
Fracture toughness of gamma-based titanium aluminides 244
Fracture toughness of roiling bearing steels 248
Fracture toughness of tool steels using chevron notched specimens 252
Fracture-induced scale effect on the modulus of rupture in quasi-brittle materials 256
From the european group on fracture to the European structural integrity society 260
Generalized path independent integral in linear fracture mechanics 266
Grain boundary fracture in the cleavage regime of polycrystalline metals 270
Influence of geometry and load case on the local stress state in wide plates with semi elliptical surface cracks 274
Influence of strain rate and solidification rate on the mechanical behaviour of Al-Si-Mg alloys 278
Influence of the heat treatment and notch orientation on the fracture toughness of a TI-6AI-4V plate 282
Information-theoretic interpretation of multifractal formalism and analysis of fracture surfaces 286
Initiation, propagation and arrest of cracks in dynamic of pipeline steels at low temperatures 290
Instrumented impact testing as a method of cleavage fracture stress determination (tempered hainitic steels) 294
Instrumented impact testing of sub-size charpy-V specimens the activity of the ESIS TC5 working party 298
Involution of JR-TR curves with low temperature aging of duplex stainless steels 302
J estimation scheme for surface cracked piping under complex loading part I. Theoretical basis 306
J estimation scheme for surface cracked piping under complex loading part II. Complex shaped Elbow solutions 311
Joining elastic plates into package along curves 316
Local criterion for cleavage fracture and fracture toughness prediction 319
Macro-super-penetration 323
Mechanical evaluation of a reversion heat treatment for a duplex stainless steel thermally embrittled 328
Mechanisms and characteristics of damage and failure in terms of the theory of phase transition 332
Microcrack toughening mutual interactions and energy dissipative mechanisms 336
Micro-fractography of cleavage fracture by EBSP technology and computer assisted stereophotogrammetry 340
Modelling intergranular crack growth in 2D and 3D voronoia cells 344
New fundamental fracture criteria 348
Non singular terms in crack tip stress distribution for plane problems 352
Nonlocal stress field in a orthotropic plate with a slanted crack 356
Numerical approach in viscoelastic fracture mechanics 360
Numerical evaluation of the anvil force for precise processing of the impact fracture test data 364
Numerical path independent integral in dynamics fracture mechanics 368
Numerical round robin on micromechanical models 372
On a functional description of non-local strength and fracture. Existance and uniqueness 376
On the effect of quasi-static loading rates upon the fracture toughness of ordinary structural steel 380
On the experimental realization of Mode II cracks 384
On the temperature in dynamic crack surface ligaments 388
On the thermo-visco-plastic instability for material failure under impact 392
On the use of dimensional analysis in fracture mechanics 396
Plastic strain distribution near a tip of a sharp V-notch in a power hardening material 401
Polycristalline plasticity and local approach of intergranular brittle fracture in A508 steel 405
Relationship between grain size and strength for 3Y-TZP ceramics 409
Scaling characteristics of stochastic damage accumulation in brittle materials 413
Scatter of a ferritic steel in the transition region analysed by Charpy tests and dynamic tensile tests 417
Shielding effects and dislocation repositioning at cleavage crack growth 421
Simple formula for stress near a crack tip in a hardening material 425
Simulation of the crack growth of 3D structures under fatigue in taking account of residual streses 429
Singularity fields of a crack meeting an inclined interface of two elastic materials and numerical results 433
Some observations of fracture surfaces of Fe-Si alloy single crystals 437
Spalling of aluminum alloy 7020-T6, experimental and theoretical analyses 441
Stability of the warm prestressing effect under subsequent loading 445
Statistical modelling of the ductile-brittle transition of ferritic steels 449
Steady state analysis of an array of semi-infinite edge cracks in a transformation toughening ceramic 453
Stochastic modeling of fatigue damage processes in metals 457
Stress intensity factor, compliance and inverse compliance formula for three-point bend specimens 463
Temperature influence of fracture toughness Klv for two thermoresisting steels 467
The solid particle impact erosion of brittle solids 470
The effect of strain rate and temperature on the impact behaviour of automobile coatings 474
The influence of surface treatments on the hertzian impact damage of glass 478
The nature of fracture in solids 482
Thermal shock experiments on cracked cladded plates 486
Thermomechanical approach of running discontinuities 490
Uncoupled dynamic fracture approach 493

RkJQdWJsaXNoZXIy MjM0NDE=